How to Install a Tub (Step By Step).
How to Install a Tub (Step By Step).
Blog Article
Here in the next paragraph you can find some first-rate details when it comes to Installing A Bathtub.
Installing a tub isn't exactly brain surgery, but it does need solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently available, the project can relocate easily; if you have to open up a wall to get rid of the old tub as well as position the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub as well as set in the new one. See to it you have qualified yourself for the task and also are comfortable attempting it. As opposed to employing a professional to take control of a halfway-completed task, it is better to think about utilizing one prior to you start. Opportunities are you might require an expert plumber to make tube links.
This post will certainly aid you mount a brand-new bath tub in your restroom if you have actually currently bought a new bathtub and also don't need to alter the setup of your previous water supply pipes.
Your tools and material checklist ought to consist of the following:
Planning for the Installation
Firstly, the supporting frame supplied with the bathroom must be fitted (if needed) according to the maker's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet connectors to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final placement.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your setup, after that the first thing you need to do is detach the supply of water. After doing so, turn on the taps to drain any kind of water staying in the system. The process of removing the existing faucets can be fairly troublesome as a result of the restricted access that is commonly the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipelines. When the supply pipelines have been gotten rid of, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Before moving on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Mounting the Tub
Using both wooden boards under its feet, put the bathtub in the needed position. The wooden boards are useful in equally spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto 4 small factors.
The next goal is to make certain that the tub is leveled all round. This can be attained by checking the level and also changing the feet on the bath tub until the level reviews level.
To set up faucets, fit the bottom of the outermost adaptable tap port to the appropriate supply pipe by making a compression sign up with; then do the same for the other faucet.
Switch on the water system and also check all joints as well as brand-new pipework for leaks as well as tighten them if needed. Fill the bathtub as well as additionally check the overflow outlet as well as the regular outlet for leaks.
Lastly, deal with the bathroom paneling as described in the maker's user's manual. Tiling as well as sealing around the tub needs to wait until the bathtub has been utilized at the very least once as this will settle it into its last placement.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier offered backnut. When the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet ports. The previous type should be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, triggering the water to pass through the wall surface between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can crack fairly very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also easily readily available on the market. It is suggested to fit the ceramic tiles using water-resistant or waterproof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very focused on How to Install a Bathtub Yourself and I am assuming you enjoyed reading the new post. So long as you liked our blog posting if you please make sure you remember to share it. Many thanks for your time. Don't hesitate to check up our blog back soon.
Additional Information Report this page